Mikuni RS40 Carb Kit- Suzuki GSFS 1200 Bandit 2000 & Later

$1,620.00 AUD$1,720.00 AUD

Description

This Mikuni RS40 carburetor Kit is for direct fitment to most Larger GSFS Bandit engines. They will breathe a whole new lease of life into your machine with an up to 25% increase in power, whilst making it perform and operate as it should with no hesitations or flat spots.

You will very quickly realize that the expense of a rebuild of your old worn OEM carbs can far exceed the cost of these new units and unfortunately as with many rebuilds now days you only have the option in many cases of gambling with very poor quality aftermarket parts. Considering this and if intending to ride and enjoy your motorcycle it makes good sense to retire your OEM carbs into the cupboard and step up to a set of RS’s.

TPS- Some later model Bandits have a throttle position sensor on the OEM carbs, where if wont run with it disconnected you will need to purchase elsewhere a Dyna S ignition system which eliminates the sensor and also offer some other performance enhancements.

Before rushing in and ordering please firstly check your carb spacing and carbie sizes for compatibility. These are not suited for downdraft engines.

This Mikuni kit comes with the carb  throttle port  center to center spacing’s listed below for direct fitment to 2000 and Later Suzuki GSFS Bandit Engines.

A= 82mm (spacing center to center between carb 1 & 2)
B= 85mm (carb 2 & 3)
C= 82mm (carb 3 & 4)

The carb total front to back length of 100 replaces your OEM carbs measuring 95 thru 100mm and comes with either a 55mm inlet outside diameter for use with POD filters or velocity stacks or with fitted sleeves increasing the inlet diameter to 58mm for standard air-box compatibility. The carb outlet diameter at the motor end is 44mm, where your engine will be 42mm making it a tight but manageable squeeze in if your rubbers are in good condition. The RS 38 and 36’s are an exact matching 42mm.

All sleeves are CNC machined, silver anodized and permanently set in place using 620 Loctite. These RS carbs have been re-spaced using new stainless steel throttle and choke shafts along with plated metal upper and lower support brackets for maximum strength and rigidity.

PLEASE SELECT YOUR CARBURETOR AIR-FILTER AND ENGINE END, OUTLET SPIGOT DIAMETERS WHEN PURCHASING 

Pilot Jet: VM28/486-17.5, Needle: 9DCHY10-99, Needle Jet: Y-6 (568 Series), Main Jet: N100.604-140

Your stock throttle cables will match to these carbs, where we also have available in the RS accessories page either our road bike throttle and cable assembly (KRS-001) or a Quick action 1/4 turn throttle and cable kit (PPQA40K)
You can also buy separately either POD filters or Velocity stacks which have no form of filter in them (15, 30,50 and 75mm long) for racing.

All international buyers are responsible for the payment of their domestic customs duties and taxes charged on imported goods. The duty free threshold and duty/taxes payable rates differ from one country to another and we strongly advise you check your liability before ordering if unsure. Please check your tracking on all international shipments within 7 days to follow their progress and determine if it is being held by your local customs dept. or on their behalf by the Postal Service, who you will need to make contact with using the provided tracking number.

Please Note: Other than exact replacement OEM carburetors, all Mikuni Aftermarket Carburetors and Tuning Components are sold “As Is” for Off Road / Racing Use Only and are not intended or approved for use on vehicles operated on Public Roads or in locations where applicable engine tampering and anti-pollution laws apply.

Additional information

Select your Carb diameters

55mm Inlet For PODs, 58mm In For Air Box

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.