1. TM38-86 38mm TM Mikuni Carburetor w 44mm spigot

(1 customer review)

$295.00 AUD

In stock

SKU: TM38-86 Category:

Description

The TM38-86 is supplied with the following factory jetting installed:

Pilot jet 22.5 (VM22/210),  Needle 6FJ41,  Needle Jet Q-2 (389 Series),  Main Jet 230 (4/042),  Air Jet none,  Slide  4.0 (832-43011)

Dimension A= 44mm, B= 100mm, C= 170mm, D= 62mm, Total Width 75mm

Unlike many motorcycle manufacturers’ purpose modified versions, these factory TM Round Slides are both 2 and 4 stroke compatible and are regarded by the factory to be the best performing version of this carburetor ever made.

Mikuni’s (flat slide) carburetor, the TM Series Carburettors provide significant performance improvements over older round slide carburetors. Air flows faster and smoother through the TM Series venturi due to the flat slide design and the jet blocks which help create smooth bore effect.The high velocity of the air flow means a stronger vacuum at the needle jet providing more precise metering and better throttle response.

Performance features for the Mikuni TM Series Carburetors include a large selection of bore sizes for increased fuel mixture flow to match engine modifications.  And the TM Series offers a wide range of tuning components to allow precise fuel mixture metering in any application, at any throttle setting, under any riding conditions.

Tuner jet kits can be purchased separately for many different motorcycles as per the corresponding  options. These kits consist of the suggested jets for changing that are not matching those factory fitted in the TM38-86, they include an extra one size up and one size down main jet for tuning the main circuit due to fuel quality variations, altitude and climate. Testing and conformation of correct main circuit jetting can only be done by physically changing jets and WOT testing.

These tuner jet sets have been determined from thirty years of experience, customer feedback, plus research and development as the Australian Mikuni distributor. From time to time these may not be exactly right for every engine, usually due to changes to porting, compression or numerous other things that contribute to the requirement for additional fine tuning but as a rule our kits are spot on or a very close and useful starting point, but we give no guarantees and sorry do not release kit details or jet size information. If you have your own spec simply purchase the carb and buy any other required jets from the jet pages. This also applies to replacing jets in other TM38’s as the 389 series needle jet and others items may not match and fit.

Keep in mind that these are suggested specs, and all tuning procedures, as found in our Tuning Tips section must be adhered to for the confirmation of any supplied jet’s compatibility with your engine.

(The picture with the cable shows the required length of inner cable protrusion and securing fitting at the carb end on basically a minimum length adjustment. The back board is divided into 1 and 10mm increments)

All international buyers are responsible for the payment of their domestic customs duties and taxes charged on imported goods. The duty free threshold and duty/taxes payable rates differ from one country to another and we strongly advise you check your liability before ordering if unsure. Please check your tracking on all international shipments within 7 days to follow their progress and determine if it is being held by your local customs dept. or on their behalf by the Postal Service, who you will need to make contact with using the provided tracking number.

Please Note: Other than exact replacement OEM carburetors, all Mikuni Aftermarket Carburetors and Tuning Components are sold “As Is” for Off Road / Racing Use Only and are not intended or approved for use on vehicles operated on Public Roads or in locations where applicable engine tampering and anti-pollution laws apply.

 

JET NEEDLE NUMBER APPLICATIONS NEEDLE DIAMETER BEFORE TAPER AIR FUEL RATIO
6FJ41 TM38 FLATSIDE 2.522 LEANERRICHER
6FM46 TM38 FLATSIDE 2.522
6FJ40 TM38 FLATSIDE 2.522
6DPO4 TM38 FLATSIDE 2.515

 

 

 


1 review for 1. TM38-86 38mm TM Mikuni Carburetor w 44mm spigot

  1. Sandy (verified owner)

    A+ for service and postage, guys were very informed with a variety of bikes and kits and had plenty of time to explain both.
    Was delivered to my door within 20 hrs from placing order.
    Very impressed with results.

Add a review

Your email address will not be published. Required fields are marked *